Air Pollution Control Innovations

Last March I gave a paper and presentation at the International Conference on Thermal Treatment Technologies and Hazardous Waste Combustors (IT3/HWC) in Houston, TX.  The paper discusses the challenges for meeting ultra-low emission limits for medical waste incinerators.  Wet scrubbers are used to control hazardous air pollutants (HAPs) on many hospital, medical, and infectious waste incinerators (HMIWI).   The Maximum Available Control Technology (MACT) standard for these incinerators was revised and became final in 2009.  The new standard has the lowest emission limits for incinerators today. The limits exceeded the capability of systems designed to the previous standard with respect to particulate matter (PM), lead (Pd), cadmium (Cd), mercury (Hg), and dioxin/furans (D/F).  By 2014 all existing medical waste incinerators were either shut down or upgraded to comply with the new standard.  Envitech successfully upgraded four existing medical waste incinerators.  A paper presented at the 2012 IT3/HWC conference describes one of these systems which was installed at the National Institute of Health (NIH), Rocky Mountain Labs.

The challenge moving forward will be new medical waste incinerators which have even more stringent, ultra-low emission limits.  Building a new incinerator requires critical decisions on control technologies and permitting.  The IT3/HWC paper reviews these issues for specific HAPs and discuss trade-offs between permitting a new medium size incinerator versus a large incinerator.   An example is provided of an air pollution control system meeting the emission requirements for a new large medical waste incinerator at the University of Texas Medical Branch (UTMB) in Galveston, TX.  Envitech is also building gas cleaning systems for two new medium size medical waste incinerators for a research facility which integrate NOx control using ozone injection.

Please click on the links below download the presentation and paper.

In 2009, the US EPA revised the emission limits for the Hospital, Medical, and Infectious Waste Incinerator (HMIWI) MACT standard. You can follow the link to the blog piece published in May 2013 on the new standard. It dramatically reduced the emission limits for several pollutants including particulate (PM), lead (Pb), and dioxins and furans (D/F). Several existing medical waste incinerators in operation at the time were not capable of meeting the new limits, especially for lead (Pb) and/or dioxin and furans (D/F). Cost effective add-on controls were needed to bring existing system into compliance with the new rules and to allow them to continue to operate.

To meet this new challenge, Envitech designed a carbon bed adsorber and filter package to be installed downstream of existing wet scrubbers. The package is comprised of a new fan to overcome additional system pressure drop. Heat of compression from the fan and a re-heater duct heats the wet gas above the dew point to prevent condensation fouling in downstream filter and/or carbon bed adsorber. The system is delivered pre-assembled on a skid to reduce installation time and cost. A cartridge filter removes low concentrations of condensed Pb particulate. The carbon bed adsorber removes dioxins, furans and mercury (Hg). Envitech has upgraded four medical waste incinerators to meet the new MACT standards. All four are operational and compliant with the new standards.

In one case for Wyoming Medical Center (WMC), space was limited for add-on controls. The system had to be installed outdoors and capable of withstanding below freezing temperatures. The existing system did not meet the new limits for lead (Pb) and dioxins/furnace (D/F).The add-on controls included a cartridge filter and a carbon bed adsorber. The equipment was insulated and heat traced to maintain temperature above the dew point after re-heat. System features include:

•  Shop and skid mounted assembly for ease of installation.
• Insulation and heat tracing for outdoor operation in a cold climate.
• Silicon controlled rectifier (SCR) controller to control the heater duct.
• Compressed air pulse cleaning for automatic particulate removal from the cartridge filters.
• Pre-wired instrumentation to a control box located on the skid.
• Manways to facilitate maintenance access.

The system has been operational since 2014 and has been used on a routine basis during cold winter months.   The system comfortably passed a stack test in 2015. Compliance for lead (Pd) is 20 times below the limit and Dioxins/Furans (D/F) is 5 times below the limit. The re-heat and filter package has been used on several other medical waste incinerators and provide a cost effective solution for meeting stringent emission limits. 

Download a free case study to find out how Wymoming Medical Center met the new EPA HMIWI emission limits for their existing medical waste incinerator.

Download a free white paper from the 2010 Internationa Conference on Thermal Treatment Technologies and Hazardous Waste Combustors (IT3/HWC) on the 2009 HMIWI MACT standard for medicl waste incinerators.

Envitech will attend the International Conference on Thermal Treatment Technologies (IT3/HWC), October 20-22, 2015 at the Crowne Plaza Hotel in downtown, Houston, Texas.  The preliminary technical program can be downloaded from the conference website.   The conference features key note speakers from Veolia, Clean Harbors, Essroc, TCEQ, and B3 Systems.

Envitech will have an exhibit booth and present a paper, “Meeting the New Hospital, Medical, and Infectious Waste Incinerator (HMIWI) MACT with a Wet Electrostatic Precipitator (WESP)”.  The paper will provide an overview of a new medical waste incinerator scrubber system with a wet electrostatic precipitator to treat the off gas from two existing medical waste incinerators. The new system was required to achieve a 20% reduction in particulate (PM) emissions, and a 93% reduction in lead (Pb) emissions from the previous gas cleaning system.  The new system has been operational since October 2014.  The table below compares the performance of the emission limits to the new compliance standards. The results demonstrate the system comfortably meets the new EPA MACT standards.